Twin carburettors have an unjustified reputation for being hard to keep in tune. Buick corteco oil seals.It’s
origins lie in the bad practice of fiddling with the carburettor of an
off-tune engine before having first checked that all else is in order –
compressions, ignition timing, distributor, advance rate, tappet
clearances, along with a lack of air leaks into the inlet manifold from
such sources as damaged gaskets or faulty brake servos.Buick corteco oil seals.
This is not clever regardless of whether you have one carburettor or several – the carb(s) should always be the LAST thing to adjust. However, typically, someone confronted with an out of tune twin carburettor engine readily recalls having heard that they are hard to tune and keep tuned, so assumes that’s where the problem is and sets about trying to adjust the carburettors to make the engine run better.Buick corteco oil seals.
As the problem was probably somewhere else, the tuning attempts are invariably doomed to failure and the engine finishes the exercise no better off than it started. “Gosh!” (to be polite!) exclaims the frustrated tuner, “It’s true! Twin carburettors ARE hard to tune!!!” And so the experience is relayed on to others and the myth is perpetuated.Buick corteco oil seals
The actual tuning procedure is quite simple: First, check that everything else is to spec (see above) – it is a complete waste of time trying to tune out a fault elsewhere by adjusting the carburettors. Next, if you haven’t had anything to do with the car before, check the condition of the carburettors – particularly wear in the throttle spindles and also the needle valves.
Air leaking through badly worn spindles will make the idle uneven and variable, and so more difficult to set since the amount of leaking air is not constant. If worn, fix the problem or expect only limited success in setting the carbs. Having done these key initial steps, following the standard tuning/balancing process outlined in the workshop manual will quickly bring the carbs into excellent balance.Buick corteco oil seals.
SU’s are at correct mixture when lifting the piston about 1-2 mm makes no difference to the idle speed (as described in the workshop manuals). If however you are measuring exhaust CO readings etc, they usually will be high, due to the siamesed inlet ports as much as anything, but also the lack of emulsified air in the droplets as they leave the jet. The readings clean up immediately the car is under load.
As the carbs get a bit of mileage, some wear does occur at the thick end of the needle, resulting in rich idle if the mixture is OK everywhere else, or weak mixture everywhere else if you set it correctly at idle. Simple solution: renew the jet needle. If the jet itself is looking oval, it will need replacing too.Buick corteco oil seals.
Having set the carbs up properly in this way (including renewing spindles etc if required), my experience with each car I have kept tuned over a period of more than twenty years is that only very minimal adjustment, usually none, is needed at subsequent tune-ups if everything else is set first. (Sorry to repeat it but it is vital).
If you don’t have ready access to a workshop manual, the tuning procedure itself is:
Adjust the throttle stops so each carb is sucking evenly (see below).
Adjust the mixture (also see below)
If there was significant adjustment needed for (2), repeat (1) & (2), or do a couple of loops through (1) & (2) if initial adjustment was major.
Adjust the linkages between carbs so that both carbs are taking up at the same time when the throttle is depressed. (Note: you should set the linkages up so that there is some free movement before the spindles start opening).
Check you are getting full throttle just as the pedal reaches full travel (so the cable doesn’t get stressed when the red mist sets in!) and adjust the cable and/or the return stop in the footwell if necessary to achieve this.The tuning is best done with air filters removed.Buick corteco oil seals.
This is not clever regardless of whether you have one carburettor or several – the carb(s) should always be the LAST thing to adjust. However, typically, someone confronted with an out of tune twin carburettor engine readily recalls having heard that they are hard to tune and keep tuned, so assumes that’s where the problem is and sets about trying to adjust the carburettors to make the engine run better.Buick corteco oil seals.
As the problem was probably somewhere else, the tuning attempts are invariably doomed to failure and the engine finishes the exercise no better off than it started. “Gosh!” (to be polite!) exclaims the frustrated tuner, “It’s true! Twin carburettors ARE hard to tune!!!” And so the experience is relayed on to others and the myth is perpetuated.Buick corteco oil seals
The actual tuning procedure is quite simple: First, check that everything else is to spec (see above) – it is a complete waste of time trying to tune out a fault elsewhere by adjusting the carburettors. Next, if you haven’t had anything to do with the car before, check the condition of the carburettors – particularly wear in the throttle spindles and also the needle valves.
Air leaking through badly worn spindles will make the idle uneven and variable, and so more difficult to set since the amount of leaking air is not constant. If worn, fix the problem or expect only limited success in setting the carbs. Having done these key initial steps, following the standard tuning/balancing process outlined in the workshop manual will quickly bring the carbs into excellent balance.Buick corteco oil seals.
SU’s are at correct mixture when lifting the piston about 1-2 mm makes no difference to the idle speed (as described in the workshop manuals). If however you are measuring exhaust CO readings etc, they usually will be high, due to the siamesed inlet ports as much as anything, but also the lack of emulsified air in the droplets as they leave the jet. The readings clean up immediately the car is under load.
As the carbs get a bit of mileage, some wear does occur at the thick end of the needle, resulting in rich idle if the mixture is OK everywhere else, or weak mixture everywhere else if you set it correctly at idle. Simple solution: renew the jet needle. If the jet itself is looking oval, it will need replacing too.Buick corteco oil seals.
Having set the carbs up properly in this way (including renewing spindles etc if required), my experience with each car I have kept tuned over a period of more than twenty years is that only very minimal adjustment, usually none, is needed at subsequent tune-ups if everything else is set first. (Sorry to repeat it but it is vital).
If you don’t have ready access to a workshop manual, the tuning procedure itself is:
Adjust the throttle stops so each carb is sucking evenly (see below).
Adjust the mixture (also see below)
If there was significant adjustment needed for (2), repeat (1) & (2), or do a couple of loops through (1) & (2) if initial adjustment was major.
Adjust the linkages between carbs so that both carbs are taking up at the same time when the throttle is depressed. (Note: you should set the linkages up so that there is some free movement before the spindles start opening).
Check you are getting full throttle just as the pedal reaches full travel (so the cable doesn’t get stressed when the red mist sets in!) and adjust the cable and/or the return stop in the footwell if necessary to achieve this.The tuning is best done with air filters removed.Buick corteco oil seals.
No comments:
Post a Comment