Amazing Quality ngk oil seals
Big price cuts.How to Replace a Ford Ranger Oil Pan Gasket.The oil pan
on a Ford Ranger pickup is mounted on the bottom of the engine block; it
collects motor oil after the oil circulates through the engine. If you
regularly notice a black puddle underneath your engine, it is a good
sign that you have an oil pan leak. Engine oil leaks are not only
environmentally hazardous–low oil levels can cause serous engine damage.
Draining the Oil Pan
1Disconnect the ground cable from the negative battery terminal, by loosening the retaining bolt with a wrench. Pull the clamp off the terminal.
2Pull the oil dipstick from the dipstick tube with your hand.
3Place a waste oil collection pan underneath the connection between the transmission oil cooler lines and the radiator. Unscrew the transmission oil cooler line fittings from the radiator, using a line wrench.
4Raise the vehicle safely using an automotive jack. Support it with jack stands placed underneath the frame.Amazing Quality ngk oil seals Big price cuts.
5Place a waste oil collection pan underneath the drain bolt on the bottom of the oil pan. Unscrew the drain bolt using a socket, and allow the oil to drain from the engine.
Removing the Oil Pan
1Label and disconnect the wires connected to the starter solenoid, using masking tape and a marker.
2Unscrew the bolts that secure the starter motor to the engine block, using a socket. Remove the starter motor from the vehicle.
3Unscrew the nuts and bolts that secure the head pipe to the exhaust manifold, using a socket and wrench. Slide the head pipe out of the way.
4Unscrew the bolts that secure the transmission oil cooler lines to the engine block, using a socket. Slide the lines out of the way.Amazing Quality ngk oil seals Big price cuts.
5Unscrew the bolts that secure the oil pan to the engine block. Lower the oil pan away from the engine block and remove it from the vehicle.
6Clean the oil pan, using an automotive solvent and allow to air dry. Be sure to remove all the old gasket material from the gasket mating surface.
7Clean the gasket mating surface on the bottom of the engine block, using a flat razor blade. Be sure to remove all the old gasket material.
1Place a light dab of RTV silicone sealant every two to three inches along the gasket mating surface on the oil pan.
2Lay the replacement gasket into position on the oil pan.
3Raise the oil pan into position underneath the engine block, using your hand.
4Screw in the bolts that secure the oil pan to the engine block, using a socket.Amazing Quality ngk oil seals Big price cuts.
5Screw in the bolts that secure the transmission oil cooler lines to the engine block, using a socket.
6Slide the head pipe into position at the rear of the exhaust manifold. Screw in the bolts that secure the head pipe to the exhaust manifold using a socket.
Installing the Starter Motor
1Raise the starter motor into position against the engine block. Screw in the bolts that secure it, using a socket.
2Reconnect the wiring harness to the starter motor, using the labels you made during disassembly.
3Screw the oil pan drain bolt into the bottom of the oil pan, using a socket.
4Screw the transmission oil cooler line fittings into the radiator, using a line wrench.
5Slide the oil dipstick into the dipstick tube, using your hand.
Testing and Inspecting for Leaks
1Lower the vehicle.
2Reconnect the ground cable to the negative battery terminal. Slide the clamp over the terminal and tighten the retaining bolt, using a wrench.
3Fill the engine with oil according to the specifications listed in the Ranger’s owner’s manual.
4Run the engine and and check the transmission oil level, using the procedure outlined in the owner’s manual.Amazing Quality ngk oil seals Big price cuts.
Draining the Oil Pan
1Disconnect the ground cable from the negative battery terminal, by loosening the retaining bolt with a wrench. Pull the clamp off the terminal.
2Pull the oil dipstick from the dipstick tube with your hand.
3Place a waste oil collection pan underneath the connection between the transmission oil cooler lines and the radiator. Unscrew the transmission oil cooler line fittings from the radiator, using a line wrench.
4Raise the vehicle safely using an automotive jack. Support it with jack stands placed underneath the frame.Amazing Quality ngk oil seals Big price cuts.
5Place a waste oil collection pan underneath the drain bolt on the bottom of the oil pan. Unscrew the drain bolt using a socket, and allow the oil to drain from the engine.
Removing the Oil Pan
1Label and disconnect the wires connected to the starter solenoid, using masking tape and a marker.
2Unscrew the bolts that secure the starter motor to the engine block, using a socket. Remove the starter motor from the vehicle.
3Unscrew the nuts and bolts that secure the head pipe to the exhaust manifold, using a socket and wrench. Slide the head pipe out of the way.
4Unscrew the bolts that secure the transmission oil cooler lines to the engine block, using a socket. Slide the lines out of the way.Amazing Quality ngk oil seals Big price cuts.
5Unscrew the bolts that secure the oil pan to the engine block. Lower the oil pan away from the engine block and remove it from the vehicle.
6Clean the oil pan, using an automotive solvent and allow to air dry. Be sure to remove all the old gasket material from the gasket mating surface.
7Clean the gasket mating surface on the bottom of the engine block, using a flat razor blade. Be sure to remove all the old gasket material.
1Place a light dab of RTV silicone sealant every two to three inches along the gasket mating surface on the oil pan.
2Lay the replacement gasket into position on the oil pan.
3Raise the oil pan into position underneath the engine block, using your hand.
4Screw in the bolts that secure the oil pan to the engine block, using a socket.Amazing Quality ngk oil seals Big price cuts.
5Screw in the bolts that secure the transmission oil cooler lines to the engine block, using a socket.
6Slide the head pipe into position at the rear of the exhaust manifold. Screw in the bolts that secure the head pipe to the exhaust manifold using a socket.
Installing the Starter Motor
1Raise the starter motor into position against the engine block. Screw in the bolts that secure it, using a socket.
2Reconnect the wiring harness to the starter motor, using the labels you made during disassembly.
3Screw the oil pan drain bolt into the bottom of the oil pan, using a socket.
4Screw the transmission oil cooler line fittings into the radiator, using a line wrench.
5Slide the oil dipstick into the dipstick tube, using your hand.
Testing and Inspecting for Leaks
1Lower the vehicle.
2Reconnect the ground cable to the negative battery terminal. Slide the clamp over the terminal and tighten the retaining bolt, using a wrench.
3Fill the engine with oil according to the specifications listed in the Ranger’s owner’s manual.
4Run the engine and and check the transmission oil level, using the procedure outlined in the owner’s manual.Amazing Quality ngk oil seals Big price cuts.
No comments:
Post a Comment